(506) 2240-6804
3D print ipad stand
10 Best iPad Accessories That You Can 3D Print
3D Insider is ad supported and earns money from clicks, commissions from sales, and other ways.
Apple has long been known for designing products that push the boundaries of innovation and technology. Unfortunately, this also means that their products are on the expensive side. If you’ve already spent several hundreds of dollars on an iPad, it’s quite disheartening to know that official Apple accessories will cost you a few hundred dollars more.
The good news is that you might not need to spend that much money if you have access to a 3D printer. Here are some of the best ideas we have seen for 3D-printed iPad accessories.
If you want to get any real work done on an iPad, the first accessory you will need is a stand. This ingenious model has you covered. This simple tablet stand is sturdy enough to support an iPad Pro. Its design allows for an adjustable tilt angle. Best of all, the stand can be folded down to a flat form factor, making it easy to stow and carry around.
When 3D printing this stand, we recommend using a filament with high rigidity and strength. ABS or PETG are good candidates. You will want to print the largest version if you are using an iPad Pro. For the base iPad model and the iPad Mini, the medium version should do just fine.
The Apple Pencil is one of the best tools for boosting your productivity when working with an iPad. The problem with the Apple Pencil is that there really isn’t any place to stow it in when you have to put it down or while you’re taking a break. This simple Apple Pencil holder seeks to address that problem.
This Apple Pencil holder has just about everything you will need. It has space to store the Apple Pencil either horizontally or vertically. It also has slots for the recharge piece and extra pencil tips. The cap that comes with the model fits very snugly with the holder, so you might have to do heavy sanding to get the pieces to fit together comfortably.
If you have kids, then you probably already know how effective an iPad is in keeping their attention.
This is something you can take advantage of on long drives. This custom bracket mounts an iPad between the two front seats of a car, effectively turning an iPad into a theater for your young backseat passengers.
To make sure that the bracket is sturdy, it is recommended that you use aluminum tubes and a few metal nuts and bolts in building it. The iPad can be slid horizontally to any point along the bracket so the viewer can sit comfortably anywhere on the backseat. Make sure your kids are all wearing seatbelts while the car is moving and the iPad is mounted to the bracket – you would not want it to cause any accidents.
Connecting a Bluetooth keyboard to your iPad is one of the best ways to make it work like a laptop. While there is an official iPad stand that incorporates a keyboard, some people find that it lacks robustness and that it positions the iPad too upright.
This custom iPad keyboard stand positions the tablet at a much more relaxed angle, making it more comfortable to use for long hours.
The stand also has a notch for the Apple Bluetooth keyboard to latch onto. This creates a working setup that feels more balanced and ergonomic. The keyboard stand is also just small enough to throw in your backpack in case you need to work on the go.
If you have ever watched a movie or played music on your iPad, you might also have been underwhelmed by the tablet’s sound quality. The limited size of the speakers means that its audio coverage is quite poor especially when you’re in a large room.
This speaker chip acts as a reflector for the audio, magnifying it for the audience positioned right in front of the tablet. There is some assembly required, and some magnets will have to be inserted into the build. This is a fun little add-on to your usual stash of iPad accessories.
6. Protective case
Making your own iPad protective case is just about one of the most fun that you can have with your 3D printer. There are lots of different designs out there such as this honeycomb cover for the base iPad, this “big grips” case for children, or this standard iPad Mini case with an engraved Apple logo.
If you have any 3D modeling skills, then you easily design a custom protective case for your iPad. We recommend using flexible filament like TPU for maximum impact resistance. PLA is also a good candidate with a good ratio of rigidity and flexibility. Just double-check all measurements before proceeding with a print – you want it to be perfectly snug.
This iPad stand isn’t the most practical, but it’s sure fun and makes for a great conversation piece. This stand is basically a single octopus tentacle that is coiled in a shape that provides support to your iPad. The standout feature of this model is that it is very detailed in reproducing the suction cups of an octopus tentacle.
The octopus stand is quite small, so you may want to scale it up for additional reinforcement. We also recommend printing it at 100% infill to reduce the chances of it being wobbly while in use.
All of us are familiar with having to deal with glare while looking up things at the screens of our devices.
This can be frustrating when you’re trying to read an e-book on your iPad while at a park or taking notes when you’re outdoors.
If this is a problem that you understand, then the solution is to just 3D print a simple sun visor or sun hood. This sun hood clips right onto an iPad Mini to shield it from the sunlight. When you’re done with your activity, just fold the sun hood and keep it in your pocket. This is the kind of accessory that you did not know you needed but will end up being one of your essentials.
Are you tired of having online meetings where the tablet is constantly facing upwards from your desk at an unflattering angle? Unfortunately, there is not much that you can do with a standard iPad stand. This articulating arm holder will solve that problem.
This arm holder can be clipped to any thick surface such as your work desk or the edges of a bookshelf. The articulated arm can be twisted, moved, and rotated in infinite ways to help you find your best angle.
With so many possible setups, this arm holder will change the way that you show up to online meetings and teleconferences forever.
The front-facing camera of iPads is among the best, especially with its smart, subject-tracking features. However, there are times when we just aren’t comfortable with having a camera constantly trained at us. If you’re getting paranoid over other people and clandestine agencies spying on you, then this simple camera lens cover is a quick solution.
There’s nothing fancy about this camera cover. It is just a plastic clip that snaps on one edge of your iPad, providing a barrier between the camera lens and the rest of the outside world. It also makes for a great gift for any of your privacy-obsessed friends.
Final thoughts
Buying into the Apple ecosystem can sometimes feel like you’re sinking into a quicksand of having to spend more and more on essential accessories. If you have a 3D printer, then there are lots of ideas to hack the system.
Make the most out of your iPad without having to spend hundreds of dollars simply by spending a few hours on your 3D printer.
Warning; 3D printers should never be left unattended. They can pose a firesafety hazard.
▷ simple ipad stand 3d printed 【 STLFinder 】
Simple iPad 2 Stand -3D printed
thingiverse
I altered the cutout to match profile for an iPad 2 using technical drawings provided by Apple for case manufacturers. ...It seems to fit pretty well.
Simple iPad 2 Stand -3D printed
thingiverse
Instructions You can customize the scad file to set the overall width of the stand, the width of the end pieces and the depth of the cross bars.
The attached stl uses 65mm for width and 10mm for the other values. ...This produces a fairly small stand...
iPad 3d printed stand
thingiverse
... time is about 100 minutes with a 0.4 nozzle. Also, you can put a tiny magnet (5×5) on the back in hinge. But this is optional. In (my blog) download, you will find also .step files. https://theveel.com/druk-3d/coviddesign-ipad-3d-printed-stand
iPad 3d printed stand
prusaprinters
... In (my blog) download, you will find also .step files. https://theveel.com/druk-3d/coviddesign-ipad-3d-printed-stand Print instructionsCategory: 3D Printer Accessories Summary I made this stand for my iPad 2th, but the shape it’s based on iPad 7th.
Simple iPad Stand Free 3D print model
cgtrader
SummaryA simple, portable iPad stand. Works better with a pair. I was looking for an elegant and compact design. Thanks Archimiedies for that. ...
Simple iPad mini stand
thingiverse
Simple iPad mini Stand with 3 different angles.
Simple iPad Mini Stand
thingiverse
2 piece portable iPad Mini stand. ... Inspired by mmmlinux's simple iPad Stand (http://www.
thingiverse.com/thing:24400). ...Print both sides and enjoy!
simple iphone/Ipad stand
thingiverse
simple ipad/iphone stand. ...Print sideway with supports for clean and fast result
Simple iPad stand
thingiverse
A simple iPad stand that holds the tablet up for easy video viewing or reading.
☆★ Simple iPad Stand ★☆
thingiverse
Simple iPad Stand. Support from iPad mini upto iPad Pro. Time lapse of the printing.
.. ...;)https://youtu.be/0H5edY7R5_8 Print Settings Printer Brand: Printrbot ...
Simple iPad Stand
thingiverse
Simple iPad stand to prop up your iPad, iPad mini or other tablet. I am always working on new stuff to print. If you interested in being the first to know when I release something new, then check out https://www.arsenalproducts.com/3d-printing...
Simple iPad Pro Stand
pinshape
SummaryI don't have a cover or keyboard or other stand for my new iPad Pro, so I designed this stand. It is fairly small so can easily bring in my backpack.
Not designed for heavy tapping on the iPad. Can handle some soft tapping in portrait mode.
Simple iPhone/iPad Stand
thingiverse
This is my design of a simple stand. I printed it with PETG at 25% infill and support. It works well with both iPhone and iPad. ...
Simple iPad Stand
thingiverse
A simple, portable iPad stand. Works better with a pair. I was looking for an elegant and compact design. ...Thanks Archimiedies for that.
Small, Simple, iPad stand
thingiverse
I was looking for a small simple iPad stand on Thingiverse and I only found bulky ones! So I decided to make my own and here it is.
The iPad sits very stable in both positions (landscape and vertically). The original stand I uploaded worked well...
Simple iPad Stand
thingiverse
Very simple, but quick to print and stable iPad stand. As far as I know, suitable for all iPads. ...On the underside there are four round cut-outs for self-adhesive 20 mm felt or rubber feet, so that the whole thing lies nice and quiet and does not...
Another simple iPad stand
thingiverse
This is another laser cut iPad stand, somewhere half way between todbot and eagleapex's efforts. Instructions Use 4mm acrylic or adjust the size of the slots accordingly! .
..I made the slots 3.8mm for...
Simple iPad Stand
thingiverse
The spacing of the stand legs is narrow enough to not get in the way of the dock connector, or the power button or volume buttons if the iPad is put in the stand upside down. Feel free to add your own engraved logos or images to the side legs! ...
iPad Mini Simple Stand
thingiverse
Yet another stand for an iPad, I made this from scratch as I just wanted a simple stand that had two angles for my ipad mini. Its a generic opening size so that I wouldnt have to take the cover off and it also fits my phone as well. ... Instructions...
Simple Ipad Stand
thingiverse
The Simple Ipad Stand is err an Ipad stand.
It's not rocket science but it does the job very well and I use mine all the time. It allows for vertical or horizontal use and can also be used as a rest to type. It also can be used as a picture frame...
Simple iPad stand
thingiverse
its an iPad stand! nice and simple. easily printable. there is also a "travel" version, where its two pieces slotted together for easy storage. Instructions UPDATE 5/9/12: slight update to the solid...
simple 3D printed frame stand
grabcad
the frame need to have a ledge at the back, and shouldn't be too high (25cm maximum) but can be pretty wide takes 15h on an ultimaker² and if you use another printer, make the print slower than normal because it is a pretty high print with not much.
..
Simple iPad Mini stand Free 3D print model
cgtrader
Simple iPad Mini stand useful for having a sturdy platform to set your iPad mini in to when watching videos etc. Fits both portrait and landscape orientations. ...
Ipad Stand 3D model
cgtrader
stand
Simple and compact iPad stand
thingiverse
This is an easy to print iPad stand. It can be taken apart, to save space.
... Instructions Print two side pices and one Bar, press them together and thats it!
Simple Ipad or Iphone Stand
thingiverse
I set it up so that, when printed, the resulting piece will fit flush into the recessed Apple logo on the stand. (95% scale of Stand's logo). I used CA glue to mount it. I think It gives the look of a professionally built product. Anyhow, image...
Simple Desk Stand for 3D Printed Watch
thingiverse
A quick and simple desk stand for the awesome 3D Printed Watch with Tourbillon
A Simple 3D Printed Robot Stand
thingiverse
It's 3D printed part that allows the robot to be left up to tests can run.
Ipad stand 3D print model
cgtrader
apple ipad stand for ipad 2/3/4
Ipad mini stand 3D model
cgtrader
Ipad mini model with a red and green stand. ...
STL file iPad stand・3D printed design for download・Cults
Easel
0,50 €
JEEP WITH ICE SCRAPER
0,50 €
Vertical laptop stand
0,50 €
Case for Apple pencil 2
0.
50 €
Monitor support
1.25 €
COMB
0,50 €
Plug GANG
Free
Keychain JACOB SMITH
Free
Best 3D Printer Files in the Gadget Category
Giraffe Themed Tablet Holder (iPad)
2.89 €
Meshbot 2
Free
Pug Dog Car Truck Bike Van Tire Tire Wheel Valve Stem Caps Cover
1.25 €
Ghost Pen Holder
2.67 €
Gopro 3+ Case with Lens Saver and Zip-tie mount
Free
SPINNING TOP FAN
Free
Mini Quadcopter fpv Racer 120mm micro FC lumenier racing F4 Brushless 1103 10.
000kv 2S Free
Universal Stand for Calendar, Pictures, Books, Tablets
Free
Bestsellers in the Gadget category
CYLINDER WALL/PISTON 2-STROKE
0,90 €
Case for PIXEL 7 PRO (two designs)
0,96 €
Halloween trick set
6.89 €
Karambit keychain spinner tiktok keyrambit NO BEARING
€1.71 -ten% 1.54€
Bumper DJI Avata
3,50 €
Bone Finger Updated
6.51 €
Seal of the V8 engine in place
0.
88 €
Mount for GoPro DJI AVATA
2,50 €
AR-15 LOWER MULTI-CAL. REINFORCED DESIGN
€8.50
wall key holder (dragon ball)
1.25 €
Application for creating a double text illusion
3,50 €
Owl - wall key holder
1.84 €
App to turn your photo into 10 kinds of decorations
€3.50
G26 frame DD26 - super reinforced
7 €
ENGINE BLOCK - WALL KEY HANGER
1,82 €
WALL KEY HOLDER - EYE (FULL COLLECTION)
1,88 €
Do you want to support Cults?
Do you like Cults and want to help us continue our journey on our own ? Please note that we are a small team of 3 people, so it is very easy to support us in maintaining activities and creating future developments.
Here are 4 solutions available to everyone:
-
ADVERTISING: Disable the AdBlock banner blocker and click on our banner ads.
-
AFFILIATION: Shop online with our affiliate links here Amazon.
-
DONATIONS: If you want, you can donate via PayPal here.
-
* INVITE YOUR FRIENDS: * Invite your friends, discover the platform and the great 3D files shared by the community!
30 Useful Ways to 3D Print at Home
In the near future, 3D printers will be just as important. at home, as with a smartphone or wireless Internet. The range of application of a 3D printer is unlike any technology of the recent past.
Mainly because 3D printing is more than just technology. In addition to helping with your devices, you can actually create non-digital objects and tools that make your life easier. and better. Here's a quick look at what you can already 3D print to update your home.
This simple stand fits many sizes of smartphones and tablets. Several power users have checked it out and Thingiverse (a public repository of 3D designs) has checked it out. No wonder it was designed by 3D printing hero Sonia Verdu. You can use it as a stand, connect it to a charger on the stand, and even hang the stand on the wall. No need to buy a coaster stand anymore!
Bluetooth is not required, you can increase the volume of your iPhone with a DIY amplifier. . It takes just over 10 hours to print, but once you do, it will turn any iPhone into a loud music player. Plus, no batteries or charging required!
Combine your smartphone stand and passive amplifier in this one amplifier + docking station. This is made for the iPhone, but several users have made it work with other smartphones that have speakers based on them. If you are not sure if your phone will work, ask the creators on this page.
How would you like to turn your $35 Raspberry Pi into a mini laptop? All you need is a Pi and a PiTFT display module to make a tiny laptop.
Print out the case, place everything as instructed in this video, and you're done. This is one of the coolest Pi-based 3D printing projects out there. projects
If you like the compact touchscreen Raspberry Pi better than the laptop above, then the Touch Pi is the one for you. Grab a Pi, a PiTFT 3.5" Gorgeous Expansion Touchscreen Expansion Module, an Adafruit Powerboost 500c, and a 2500mAh lithium polymer battery. Put it all in this two-piece case and you have a portable Touch Pi!
The most common problem with iPhone chargers and other USB cables is how they eventually wear out. It's super frustrating and new cables are expensive. Instead, print out these cable protection inserts to protect both ends of your standard Apple Lightning cable from damage.
Like Lightning USB cables, headphone cables tangle and break. It all comes down to good cable management. This buffered headphone holder will keep your in-ear headphones free and in good shape while keeping them compact.
Most of us have a mess of USB cables lying around our desks or around the house. Instead, plug them into this simple USB cable holder that you can attach to the wall to clean up your desk clutter, or keep on your desk to stay organized. These simple utilities make 3D printers so cool.
We used to call it a must-have accessory for clean Mac desktops. , but now you can just print it. Make as many simple desktop cable holders as you want to keep your desktop free of wire clutter.
Wire spools are one of the foundations of proper cable management. It's also a great way to keep the wire connected for shorter than its full length, but lengthen it when you need to. Make yourself some simple cable spools and watch your wire clutter disappear. Oh yes, you can scale it up as needed, so it will work with anything from a simple USB cable to a large device.
Like USB cables, AC adapters also make a big mess, especially for devices you don't use often.
And those big forks take up more space than they should store. The AC adapter organizer is a smart way to keep them all in one place, and it avoids drawer clutter.
You need simple AA or AAA batteries for most things in your home. Where is it when you need it? Print out these AA or AAA size battery dispensers and hang them wherever you like. Just keep the dispenser full and you'll never run out when you need it most.
Some electronics still need those big fat C batteries, but they probably don't have them at home. Don't worry, you just need a simple AA battery and this converter. That's right, the only difference between them is the size that this converter fixes. Just like how you can convert AAA battery to AA battery.
BladeKey is the key organizer you always wanted but never knew where to find. Your keys may differ in size from your neighbors. So how do you find the perfect key organizer for your keys? Do it yourself!
The BladeKey is adjustable in length, width and width so all your keys fit perfectly in this compact case.
Turn them one by one. No more rumble, no more dirty piles of metal in your pocket; You can solve life's problems with 3D printing.
Carabiners are one of the most useful tools in your home. They can organize thousands of things in any room, from your garage to your bathroom. Whenever you need it, simply print out a durable flexible door carabiner that has been measured with a force of 236 Newtons.
You can never have too many paper bag clips. Say it with me guys, you will never, ever, ever have too many paper bag clips. If your printer is quiet and wondering what you can do with it, just set it up to print more of these simple bag clips.
If you've never been able to justify the cost of a citrus juicer, treat yourself to 3D printing. This is one of those little kitchen tools that make life easier. Once printed, make sure you wash it and dust it once with alcohol just to be on the safe side - this goes directly to your food after all.
One-Handed Bottle Opener [No Longer Available]
What do you mean you use two hands to open a bottle? You are a Neanderthal! Download this disposable bottle opener now and print it out to wow (and wow your friends).
By the way, you will also need a small coin.
You don't want to waste those few pieces of toothpaste that are left in the tube, but man, it's hard to squeeze out the last drops. Instead, print out this tubular juicer and let it do the work for you. It fits most toothpaste tubes and even has a lock to prevent the tube from unrolling.
Soap dish is handy to have. A soap dish that sticks to your wall without any drilling is a must. This 3D printed soap dish uses two medium sized suction cups to attach to your bathroom wall. Absolutely brilliant and you can just print another one at any time.
Pliers
Don't you ever have pliers handy when you need them? Save yourself a trip to the hardware store. You can assemble this fully functional plier set in 20 minutes. Download, print, paste in place, and you're done.
It's best to block important keys and USB drives while waiting for company. This simple five-digit code safe is the easiest way to get the job done.
Now you don't have to worry about your nephew sticking your work stick in as a "joke".
Purchase of sucker stands. You can't personalize them other than printing cheese photos or one-liners! 3D printing coasters come in a variety of shapes and sizes, so choose what you like, such as the video game coasters above. Also, it's a good starting point for those who want to tinker with their own CAD drawings.
It's incredibly frustrating when you lose one item from a set of measuring cups. While 1/2 and 1 part of a tablespoon are easy to find in stores as separate parts, the rest are not. Instead, just print your own to have your set ready again.
The prettiest looking tape dispenser you'll ever own is something you can't buy in a store. Check out the Tentacle Tape. Isn't that cool? You can print it as a serrated version or a version where you fit your own knife point.
Oh my god, this is the greatest invention since sliced bread.
Once purchased, plastic bags cut into every inch of your arm. Get rid of the pain with these nifty plastic handles. Forgot one or lost it? Don't worry, just write another one. Hooray!
Bird Feeder 4.0
Printed Nest has been experimenting with a 3D printed bird feeder for a long time. If you want a bird feeder without paying a dime, use it. It's strong, it can stick to your windows, and you don't have to be an expert. Print it out, follow the instructions to install it, and you're done.
Forgot to water your plants or herbs? No problem. The self-sowing seeder will take care of this. Fill it up once a week and it will take care of the watering for you so your scattered bug doesn't damage your plant.
You don't have to spend a lot of money to get a nice little colorful lamp in your home. Paint the Voronoi Mushroom Light any shade you want and place it in a regular LED bulb. Tuh-yes, mood lighting on the cheap! Even the first version is pretty cool.
