Best 3d printers reddit

Purchase Advice Megathread - October 2022 : 3Dprinting

Welcome back to another purchase megathread!

This thread is meant to conglomerate purchase advice for both newcomers and people looking for additional machines. Keeping this discussion to one thread means less searching should anyone have questions that may already have been answered here, as well as more visibility to inquiries in general, as comments made here will be visible for the entire month stuck to the top of the sub, and then added to the Purchase Advice Collection (Reddit Collections are still broken on mobile view, enable "view in desktop mode").

If you are new to 3D printing, and are unsure of what to ask, try to include the following in your posts as a minimum:

• Your budget, set at a numeric amount. Saying "cheap," or "money is not a problem" is not an answer people can do much with. 3D printers can cost $100, they can cost $10,000,000, and anywhere in between. A rough idea of what you're looking for is essential to figuring out anything else.

• Your country of residence.

• If you are willing to build the printer from a kit, and what your level of experience is with electronic maintenance and construction if so.

• What you wish to do with the printer.

• Any extenuating circumstances that would restrict you from using machines that would otherwise fit your needs (limited space for the printer, enclosure requirement, must be purchased through educational intermediary, etc).

While this is by no means an exhaustive list of what can be included in your posts, these questions should help paint enough of a picture to get started. Don't be afraid to ask more questions, and never worry about asking too many. The people posting in this thread are here because they want to give advice, and any questions you have answered may be useful to others later on, when they read through this thread looking for answers of their own. Everyone here was new once, so chances are whoever is replying to you has a good idea of how you feel currently.

Reddit User and Regular u/richie225 is also constantly maintaining his extensive personal recommendations list which is worth a read: Generic FDM Printer recommendations.

Additionally, a quick word on print quality: Most FDM/FFF (that is, filament based) printers are capable of approximately the same tolerances and print appearance, as the biggest limiting factor is in the nature of extruded plastic. Asking if a machine has "good prints," or saying "I don't expect the best quality for $xxx" isn't actually relevant for the most part with regards to these machines. Should you need additional detail and higher tolerances, you may want to explore SLA, DLP, and other photoresin options, as those do offer an increase in overall quality. If you are interested in resin machines, make sure you are aware of how to use them safely. For these safety reasons we don't usually recommend a resin printer as someone's first printer.

As always, if you're a newcomer to this community, welcome. If you're a regular, welcome back.

Best 3D Printer Under 1000 Reddit : 3dPrintersMania

Best 3d printer under $1000 reddit on 2020-21.

• Best Overall: Prusa i3 MK3. reddit best 3d printer

• Best Value: Creality Ender 3.

• Best For Your Desk: Monoprice Maker Mini Pro.

• Best Value Delta: Monoprice Mini Delta.

• Best Value Resin: AnyCubic Photon. Best 3d printer under 1000 reddit

For Moe Details: https://3dprintersmania.com/

For the last five years we've invested in the 3D printing world, using as many printers as we can to see what is good and what is bad. We all know that printing can be expensive — there are machines out there that start at $3,000 and go up from there — so we want you to have some idea of what you can get for cheaper. When it comes to value and quality you can't beat the Prusa i3 MK3. While it isn't the cheapest of the machines on this list, it is easily the best quality in terms of build and print.

Best Overall:

Prusa i3 MK3

Best Value:

Creality Ender 3

Best For Your Desk:

Monoprice Maker Mini Pro

Best Value Delta:

Monoprice Mini Delta

Best Value Resin:

AnyCubic Photon

Best Overall: Prusa i3 Mk3

In the world of hobbyist 3D printing, there are few names as well known as Josef Prusa. His work in open source 3D printing has revolutionized what can be done at home and on a budget for those who want to create amazing prints. The Prusa i3 MK3 is the latest machine based on his open source design and is easily the most advanced printer in this list.

The Prusa has automatic bed leveling, making each print start the best it can, but it also corrects the print on-the-fly if anything happens to shift the bed. With a sensor in the extruder, the Prusa can tell when you run out of filament, pause the print, and alert you to add more, saving countless mistakes in the process. From the removable bed to easily being able to remove prints without breaking them to the excellent save function, which stops your prints being lost in a power cut, the Prusa goes out of its way to make every print work.

The listing is for the kit version of the i3 mk3 so you will be required to build it yourself. Prusa does supply a fully made one but it's $200 more when you add in the extra shipping. Which one you buy will depend on your preference, but we recommend getting the kit. Plus, it's actually a lot of fun learning to build one from scratch.

Pros:

Auto bed leveling

Excellent print quality

Open source

Active community

Save functionality

Cons:

Cheaper to buy the kit

Best Overall

Prusa i3 MK3

Fantastic quality

If you are just starting out in the 3D printing game and you want to start off with the best, then go for the Prusa MK3.

$750+ at Prusa Research

Best Value: Creality Ender 3

The Creality Ender 3 is a shining example of how a community can get together, take something cheap and flawed, and turn it into something special. The Ender 3 is not a printer for someone who wants quality prints straight of the box — you have to earn them. Sure, it's easy to get set up and it doesn't take much other to put together — just a few screws —but to get a print that you can be proud of takes effort.

The Ender 3, while being cheap, it is not configured well by Creality. The extruder setup is poor, as are a lot of the acceleration settings and because of that, it can take endless fine-tuning. Don't be dismayed though, there are people out there who are willing to help put you on track.

I never would have gotten the Ender 3 to the point of usability without the help of the Facebook and Twitter 3D printing communities, and I strongly urge you to look into those places if you intend to buy an Ender 3. Especially check out Filament Frenzy on Twitter. He can make the Ender 3 sing and dance like magic.

Of course, if you have the time to spend on it, $220 for a full-size printer that can make some fantastic prints is a bargain. If you have time to love it, it can be a great investment.

Pros:

Extremely cheap

Simple setup

Can create amazing prints

Cons:

Can take a lot of work to get right

Best Value

Creality Ender 3

Community favorite

The Ender 3 can be a real pain to get right, but when you do it can some amazing prints. Make sure you join some communities for help.

$230 at Amazon

Best For Your Desk: Monoprice Maker Mini Pro

If you are completely new to 3D printing and want something simple, reliable, and cheap, you can't do much better than Maker Mini Pro by Monoprice. The printer itself is small enough and quiet enough to sit on the desk in your office and allow you to make small, fun little projects fairly quickly. The Mini has several high-end features like Wi-Fi connectivity, along with the SD Card and direct PC connection that you normally get with larger printers.

It even comes with auto bed-leveling, which can be picky but is a great addition. There's also a heated bed for printing with multiple types of filament, something you'd expect on a more expensive printer, all wrapped in a sturdy metal body that reduces the "noise" often associated with cheaper printers. With a 4.75-inch print bed, the Mini is the smallest of the printers on this list, but if you are just starting out in 3D printing and only want to experiment, the small bed is more than enough.

With the Bowden extruder setup already a part of the Mini the results of printing are significantly better than I ever thought a $200 printer would produce. I helped my local youth room purchase three of these so the young people there can learn how to design and print in 3D and so far the only issue I have had is a blocked nozzle and an uneven print bed, both of which are the basic foibles of 3D printing and easily fixed by anybody.

Pros:

Auto bed leveling

Fits on your desk

Wi-Fi printing

Heated bed

Cons:

The print bed is really small

Best For Your Desk

Monoprice Maker Mini Pro

Teeny desk printing

Sometimes you just want a little fun at your desk. The Mini Pro is perfect for a desktop 3D printing setup.

$200 at Amazon

Best Value Delta: Monoprice Mini Delta

When I first used the Mini Delta I was ready to write it off from the start — $160 for a delta printer? It was obviously going to suck. Turns out, I was wrong. I like the Delta for a lot of reasons including its portability, it's build quality, as well as its great print quality. None of those things are as awesome as the price though. For just $160 you can have a 3D printer of your own that works as soon as you turn it on.

The interface on the Mini Delta is incredibly simple, making it perfect for youngsters and first-timers who aren't interested in taking things apart to make them work. The printer has three buttons and each one is self-explanatory, helping you get printing straight away. The nature of delta printers — delta printers use three constantly moving servo arms instead of rods and screws — means this mini model is dependable, even when being jostled. A delta, once dialed in, will give you great prints even under the worst of circumstances.

I was blown away by the print quality of this little machine and, even though it can only make really small models, it remains one of my favorites to have close by for small, quick jobs. The only issue I sometimes have is the auto-leveling is sometimes a little off and you will need to manually adjust or use a product like Magigoo to help keep it all stuck down.

Pros:

Solid as a rock

Great print quality

Simple interface

Portable

Cons:

Small

Bed leveling is janky

Best Value Delta

Monoprice Mini Delta

Mini dependability

The Mini Delta is an amazing little machine with some advanced features. The print quality is excellent and the portability is superb.

$160 at Amazon

Best Value Resin: AnyCubic Photon

Resin printing can be expensive. The machines themselves are normally high-priced and the resins can be even pricier. Resin printing differs from the other printers on this list because it uses a liquid plastic that is cured over a UV light or shot with a laser. It can be messy, difficult, and a little dangerous so it's best to know what you want before you buy.

Somehow Anycubic made an affordable resin printer that produces some of the best quality prints I've seen from a printer under $2,000. The prints from a resin printer are gorgeous and are often impossible to tell that they are 3D printed. They often look like injected molded models.

Using Chitubox — a slicer now used by a large number of 3D printer manufacturers — to slice the models is simple and effective and makes the entire process of printing models on the Photon a breeze. One word of warning though: make sure your supports are thick in Chitubox since they can be a little wimpy if you aren't careful.

Of all the resin printers that I have owned and used the Photon is the one I recommend to friends, and therefore to you, dear readers. It's dependable and accurate every time.

Pros:

Entry level price

Almost invisible layer lines

Simple to use

Excellent slicing

Cons:

Small build plate

Chitubox can be tricky

Best 3D Slicers for 3D Printers (2021)・Cults

3D printing is possible thanks to three main elements: 3D printer, 3D model and 3D cutting software. The latter, known as a "slicer", is the middleman that prepares your chosen model before sending it to the 3D printer. There are many free and paid 3D programs on the market for users. This selection of the best slicers is designed to help you choose the one that best suits your needs. nine0003

Cura is the most widely used slicer on the market. The software was developed by Ultimaker, a leading manufacturer of FDM 3D printers. Its advantage is that it is open source, free and compatible with the vast majority of desktop 3D printers and with a computer running Windows, Mac or Linux systems.

Cura slicer works with many 3D formats such as STL, X2D, 3MF, OBJ as well as image formats such as BMP, PNG, GIF, JPG. Its accessible interface is suitable for both beginners and professionals. Its features include: outline display, material usage, and print time calculation. For more advanced users, there are third-party plugins. nine0003

3DPrinterOS is a full-featured 3D slicer that can be accessed not only through a browser, but also through Windows or Mac. It is a cloud-based platform that has a slicing application, as well as a number of other functions required for 3D printing, such as repair.

Slicer gives you the ability to manage machine files in your company in a very simple way. The 3DPrintersOS platform includes three slicing apps: Cloud Slicer, Slicer 2, and Marketbot Slicer. It is also compatible with a wide range of printers. nine0003

IdeaMaker is a free 3D slicer that is often preferred for its convenience. It was released by Raise3D, a manufacturer of 3D printers. It is quite easy to use, just 4 clicks to start preparing various 3MF, OBJ and STL files. You can also customize the software to get much more advanced functionality.

IdeaMaker works with most FDM printers and with Windows, Mac or Linux operating systems. The software can also be used as a 3D printer control platform. For example, it gives you the ability to monitor different print profiles, remotely manage a running print, and easily switch between print settings. nine0003

Keep it Simple Slicer or KISSlicer is a fast, cross-platform application that you can have on Windows, Mac, Linux or Raspberry Pi. Depending on the version you choose, its interface may be more complex.

You will find a free version, which is probably suitable for beginners, as well as a paid professional version. The latter has additional features such as dual extrusion 3D printing.

Compatible with Windows, Mac and Linux operating systems, Repetier-Host is a free and open source 3D cutting software widely used in the RepRap community. Slicer offers a complete solution. It supports up to 16 extruders and can work with multiple filaments and colors at the same time to give you an idea of ​​the result before you start printing. nine0003

Repetier-Host includes 4 slicers (Skeinforge, CuraEngine, Slice3r, Slic3r Prusa Edition) but allows you to add the solution of your choice. Thus, the slicer is compatible with almost all FDM 3D printers. It has an interesting feature built in that allows you to download or duplicate all models that match your print tray and print them at the same time.

Free and open source, OctoPrint is a 3D slicer and web interface for your 3D printer. It is compatible with Raspberry Pi, Windows, Mac, Linux operating systems and allows you to control all actions through a web browser or from other portable devices. Based on CuraEngine, OctoPrint cuts your files directly. nine0003

Astroprint is designed in a similar concept to OctoPrint. It is used in the browser and with Raspberry Pi and pcDuino systems. You have 3D cutting software and the ability to control your 3D printer from any device connected to the internet.

The 3D printing software has two modes. An easy mode where you can choose the material and quality before sending it to the 3D printer. In advanced mode, you can improve the settings for better results. nine0003

Simplify 3D is specially designed for professional users. The software is compatible with Windows, Mac and almost all 3D printers. Through partnerships with 3D printing companies in over 30 countries, Simplify 3D supports over 100 printers. Your device can also be easily added if it is not listed. This means that the same 3D slicer can be used when printing on a new machine.

Another advantage of this 3D cutting program is the simulation before printing, which allows you to test. This is a very realistic feature that allows you to check prints in advance and identify any problems. In addition, the slicer is able to automatically suggest where the supporting material should be improved. nine0003

This page has been translated using machine translation. Suggest the best translation

Previous

Next

Best resin 3D printers of 2022

Buying a 3D printer can be quite intimidating, especially if you don't know much about this hobby. Best polymer 3D printers cost between $200 and $2,000, so it's no coincidence choice. Before you make a purchase, you need to think about what exactly you want to use it, as it will greatly influence the choice of printer. For example, if you plan to create large miniatures or prototypes tools, you will need a printer with a large build volume. you also you need to decide what level of detail you want from the printer, as this greatly affects its value. While a 4K-capable printer in our days is quite affordable, 6K will raise the price significantly. nine0003

Build volume is a measure of how how big a product a 3D printer can produce. If you want to do something large, you will need to purchase a printer with a large (or even very large) print volume. Generally speaking, printers with large build volumes require a bit more fiddling (and can be more error prone user) than their equivalents with standard volumes.

3D printer LCD resolution will determine the level of detail of your beautiful miniatures. Printer 4K in these days is considered the standard for all but ultra-budget models, and its more than enough for most projects. nine0003

Monochrome 3D printer LCD masking is better than a printer with RGB (or color) masking LCD display. Monochrome transmits UV light better than their color alternatives, which means each layer is scanned much faster.

Ultimately, it's up to you which of the above features is more important to you. Each of the following polymer 3D printers excel in one area or another, often several.

0.01

ANYCUBIC Photon Mono X offers the best vital features for the price of any 3D printer consumer grade polymer-based.

Premium feature set, reasonable price, speed. But the disadvantage may be that it is not as easy to use as entry level models.

Mono X function set for head above normal. With dimensions 7. 5x4.7x9.8" Mono X build area more than enough for any thumbnail you might want build. It also offers high speed, 4K resolution and better Z-axis support than similar models.

ANYCUBIC Photon Mono 4K excellent copes with the creation of standard thumbnails quickly and easily, and it is not difficult master.

Among the advantages are the price, speed and ease of use. Cons - standard build volume and possible problems with the touch screen. nine0003

He may be smaller than his older brother, Mono X, but it still packs a punch.

Excellent 4K resolution and standard build volume make it a very good option for users, who want to make a large number of standard miniatures without much fuss. It is fairly easy to set up, even for beginners, and its compact size means he can stand at the small end of the table without attracting a lot of attention.

Elegoo Mars 3 is perhaps the most a well-known 3D printer among beginners and experts.

Pros: very popular and intuitive, good resolution, slightly larger build volume. Minuses: more expensive than analogues.

Overall, Mars 3 lives up to its reputation as the easiest-to-use resin printer, and offers a robust set of features. Mars 3 is slightly better than its main competitor Mono 4K, in almost all significant categories, especially in terms of volume assemblies. However, reviews show that over time it is not as fast as the Mono 4K. However, due to its popularity on Reddit and YouTube, one can find absolutely a ridiculous amount of tutorials on how to use Mars 3 and that gives it slight edge in the beginner-friendly category. nine0003

Best high-end: original Prusa SL1S Speed ​​Bundle.

Pros: speed, really professional level, supports simple post-processing. Cons: price, some deprecated features.

The world of resin 3D printing has hobbyists and small businesses. If you want to make serious money by selling your thumbnails or other products on stores like Etsy and you already have some resin printing experience, the Prusa S1LS Speed ​​is a good option.

Learn more

• 
  3D print composite
• 
  3D printing and laser cutting
• 
  3D print iem shell
• 
  3D printing metal filament
• 
  Ikon 3d printed house
• 
  Top 10 3d printer projects
• 
  Rubik's cube 3d print model
• 
  Buy ultimaker 2 3d printer
• 
  3D printing house machine
• 
  3D print skirt
• 
  3D printed gun plans website