Mazinger z 3d print

Gambody STL files of Mazinger Z for 3D Printer

This 3D Model consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Mazinger Z 3D Printing Model comes in 1 version for FFF/FDM 3D printers. STL files of the version are available for download after the purchase.

Detailed information about this 3D printing model is available in the DESCRIPTION section.

version: FFF/FDM 1.0
File Name File Size Time / Filament Object Size
(x/y/z mm)
1_head (repaired). stl
1.39 MiB 1 h 33 min
1 m
47 x 27 x 28
2_collo (repaired).stl
0.29 MiB 19 min
19 x 17 x 15
3_perno_collo1 (repaired) . stl
0.69 MiB 13 min
10 x 10 x 14
4_Shoulder1_R (repaired). stl
0.16 MiB 35 min
26 x 13 x 23
5_Shoulder2_R (repaired). stl
0.14 MiB 34 min
26 x 13 x 23
6_Upper arm_R (repaired). stl
0.24 MiB 51 min
18 x 18 x 24
7_Upper arm2_R (repaired) . stl
0.22 MiB 30 min
18 x 18 x 21
8_Upper arm3_R (repaired) .stl
0.02 MiB 8 min
8 x 17 x 6
9_Upper arm4_R (repaired) . stl
0.45 MiB 19 min
16 x 16 x 14
10_Upper arm5_R (repaired ).stl
0.97 MiB 21 min
22 x 16 x 11
11_Arm_R (repaired). stl
0.73 MiB 1 h 58 min
1 m
26 x 28 x 41
12_Hand1_R (repaired).stl
1.38 MiB 34 min
20 x 17 x 19
13_Hand2_R (repaired). stl
0.06 MiB 13 min
17 x 8 x 13
14_Hand3_R (repaired).stl
0.40 MiB 4 min
15 x 12 x 4
15_Hand4_R (repaired). stl
0.39 MiB 5 min
15 x 12 x 4
16_Hand5_R (repaired).stl
0.40 MiB 4 min
15 x 12 x 4
17_Hand6_R (repaired). stl
0.41 MiB 4 min
15 x 10 x 4
18_Shoulder1_L (repaired) .stl
0.16 MiB 35 min
26 x 13 x 23
19_Shoulder2_L (repaired) . stl
0.14 MiB 34 min
26 x 13 x 23
20_Upper arm_L (repaired) .stl
0.24 MiB 51 min
18 x 18 x 24
21_Upper arm2_L (repaired ). stl
0.22 MiB 30 min
18 x 18 x 21
22_Upper arm3_L (repaired ).stl
0.02 MiB 8 min
8 x 17 x 6
23_Upper arm4_L (repaired ). stl
0.45 MiB 19 min
16 x 16 x 14
24_Upper arm5_L (repaired ).stl
0.97 MiB 21 min
22 x 16 x 11
25_Arm_L (repaired). stl
0.73 MiB 1 h 58 min
1 m
26 x 28 x 41
26_Hand1_L (repaired).stl
1.38 MiB 34 min
20 x 17 x 19
27_Hand2_L (repaired). stl
0.06 MiB 13 min
17 x 8 x 13
28_Hand3_L (repaired).stl
0.40 MiB 5 min
15 x 12 x 4
29_Hand4_L (repaired). stl
0.39 MiB 5 min
15 x 12 x 4
30_Hand5_L (repaired).stl
0.40 MiB 4 min
15 x 12 x 4
31_Hand6_L (repaired). stl
0.41 MiB 4 min
15 x 10 x 4
32_boomerang (repaired).s tl
0.08 MiB 1 h 19 min
1 m
74 x 34 x 13
33_missile door (repaired ). stl
0.23 MiB 25 min
20 x 12 x 19
34_Hip_joint (repaired).s tl
1.40 MiB 20 min
29 x 14 x 12
35_Shoulder_joint_x2 (rep aired). stl
0.16 MiB 26 min
11 x 11 x 24
36_Torso_joints_x2 (repai red).stl
0.68 MiB 13 min
11 x 11 x 14
37_Torso1 (repaired). stl
6.18 MiB 3 h 17 min
2 m
62 x 39 x 22
38_Torso2 (repaired).stl
4.16 MiB 3 h 7 min
2 m
62 x 39 x 21
39_Torso3 (repaired). stl
1.41 MiB 1 h 54 min
1 m
52 x 31 x 18
40_Torso4 (repaired).stl
1.57 MiB 1 h 39 min
1 m
52 x 31 x 17
41_Torso5 (repaired). stl
1.00 MiB 2 h 36 min
2 m
45 x 30 x 30
42_hp1 (repaired).stl
1.13 MiB 31 min
14 x 32 x 17
43_hp2 (repaired). stl
0.07 MiB 5 min
15 x 9 x 7
44_hp3 (repaired).stl
0.08 MiB 5 min
15 x 9 x 7
45_Upper leg1_R (repaired ). stl
1.06 MiB 1 h 13 min
1 m
25 x 53 x 13
46_Upper leg2_R (repaired ).stl
1.12 MiB 1 h 13 min
1 m
25 x 53 x 13
47_Knee1_R (repaired). stl
0.04 MiB 37 min
15 x 36 x 12
48_Knee2_R (repaired).stl
0.04 MiB 10 min
8 x 20 x 7
49_Knee3_R (repaired). stl
0.09 MiB 27 min
15 x 15 x 17
50_Ankle joint_R (repaire d).stl
0.68 MiB 13 min
10 x 10 x 14
51_Leg1_R (repaired). stl
1.34 MiB 2 h 44 min
2 m
37 x 68 x 18
52_Leg2_R (repaired).stl
1.41 MiB 3 h 16 min
2 m
37 x 73 x 20
53_Foot_R (repaired). stl
0.91 MiB 1 h 56 min
1 m
34 x 47 x 24
54_Upper leg1_L (repaired ).stl
1.12 MiB 1 h 13 min
1 m
25 x 53 x 13
55_Upper leg2_L (repaired ). stl
1.11 MiB 1 h 14 min
1 m
25 x 53 x 13
56_Knee1_L (repaired).stl
0.04 MiB 37 min
15 x 36 x 12
57_Knee2_L (repaired). stl
0.04 MiB 10 min
8 x 20 x 7
58_Knee3_L (repaired).stl
0.09 MiB 27 min
15 x 15 x 17
59_Ankle joint_L (repaire d). stl
0.68 MiB 13 min
10 x 10 x 14
60_Leg1_L (repaired).stl
1.34 MiB 2 h 44 min
2 m
37 x 68 x 18
61_Leg2_L (repaired). stl
1.41 MiB 3 h 16 min
2 m
37 x 73 x 20
62_Foot_L (repaired).stl
0.91 MiB 1 h 56 min
1 m
34 x 47 x 24
Keychain (repaired). stl
0.35 MiB 23 min
30 x 30 x 2
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5


Mazinger Z is credited as the first piloted giant robot, the titular mech of Mazinger Z Japanese manga series. The titanic robot was constructed by Doctor Juzo Kabuto using newly-discovered hyper-alloy “Super Alloy Z”. With the main element of the metal alloy being fictional Japanium that is noted to be even stronger than steel, the mech can boast of extremely high durability. Creation of Mazinger Z robot within the series of the same name is considered to mark the launch of the Super Robot genre into existence. The author of the model spent 160 hours to design and engineer the awesome 3D printing model to rejoice the anime television series fans. And Mazinger Z will definitely become a gem in your 3D printed collection - thanks to the 3D artist’s hard work and creative approach the robot is fully articulated! The Japanese super robot is depicted as it appears in the original 1972 series - with large fins on the chest to enable its Photonic Energy reactor and the control centre Hover Pilder to host the pilot. The giant mech is an excellent ally to fight the evil especially given that conventional weapons can affect its armour even not in the slightest.


Mazinger Z model for 3D printing is a highly articulated assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 32 hours in total. In order to ensure the robot’s multidirectional movement, it was divided into many assembly parts and all model’s joints were designed to presuppose the introduction of a certain mechanism to give you an opportunity to display Mazinger Z in a variety of positions, i.e. robot’s head, shoulders, arms, elbows, hands, hips, knees, feet and even fingers are movable. The Breast fire fins on Mazinger Z's chest are also provided as a separate file for you to receive the cleanest printed result. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. In order to assemble the model, you will need 2x14 mm self-tapping screws and short pieces of 1. 75 PLA to make pins. Apply the glue where you feel appropriate. Make sure to watch "Assembly video" in the photo preview section and read the author's "Assembly Manual" that comes with STL files.

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Mazinger Z's actual height that is 18000 mm. The 3D printing model's chosen scale is 1/72 for the FFF/FDM version.


FFF/FDM 1.0 version features:
- Contains 62 parts;
- A printed model is 250 mm tall, 110 mm wide, 54 mm deep;
- Each robot’s joint is articulated which allows the model's movability;
- The model can be assembled with 1.75 PLA pins and 2x14 mm screws;
- Watch "Assembly video" to see the screws coloured red and pins - yellow; 
- With any file of the model, you will also receive author’s instructions on the assembly peculiarities in a PDF file "Assembly Manual";
- All parts are divided in such a way that you will print them with the smallest number of support structures.


- STL files of Mazinger Z​​ Model for 3D printing which consist of 62 parts;
- High-poly detailed model of Mazinger Z;
- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the model of Mazinger Z​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Mazinger Z​ 3D Printing Model at Gambody YouTube channel.

Also, you may like another Robot 3D Printing Models as well as other Anime 3D Printing Figurines.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for Cura, Simplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: Use ABS or PLA Plus filament to print more durable and friction resistant details.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0. 4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 80%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0. 04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22. 5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 3 mm
Support Z Distance: 0. 1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0. 01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6. 00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 80%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45. 0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill density: 80%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0. 1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0. 42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Mazinger Z Gambody 3D Prints STL File

Etsy is no longer supporting older versions of your web browser in order to ensure that user data remains secure. Please update to the latest version.

Take full advantage of our site features by enabling JavaScript.

  • Click to zoom

503 sales |

5 out of 5 stars

€3. 13


VAT Included

Explore related categories

Listed on Oct 12, 2022

21 favorites

Report this item to Etsy

Choose a reason…There’s a problem with my orderIt uses my intellectual property without permissionI don’t think it meets Etsy’s policiesChoose a reason…

The first thing you should do is contact the seller directly.

If you’ve already done that, your item hasn’t arrived, or it’s not as described, you can report that to Etsy by opening a case.

Report a problem with an order

We take intellectual property concerns very seriously, but many of these problems can be resolved directly by the parties involved. We suggest contacting the seller directly to respectfully share your concerns.

If you’d like to file an allegation of infringement, you’ll need to follow the process described in our Copyright and Intellectual Property Policy.

Review how we define handmade, vintage and supplies

See a list of prohibited items and materials

Read our mature content policy

The item for sale is…

not handmade

not vintage (20+ years)

not craft supplies

prohibited or that use prohibited materials

not properly labeled as mature content

Please choose a reason

Tell us more about how this item violates our policies.Tell us more about how this item violates our policies.

Great Mazinger STL file z・3D printing design for download・Cults

Mazinger Z Collection

20 €


14 €


6 €

Essen Mazinkaiser with sword

6 €


1 €


4 €


5 €


14 €


5 €


6 €


8 €

Mazinger Z Collection

20 €

Best 3D Printer Files in the Miscellaneous Category


5. 11 €

Animated R5-D4 head (Droids)


Stencil Frame

2,37 €

fishing Lure for Bass - snake lure(2color)


HYPR "Sten" yoke - Lazy Iron sight delete


Captain Toad Lamp

7.15 €

Darth Vader Minion STL

9.85 €

Hive Frame Holder


Bestsellers in Miscellaneous category

4th planet Fighting pre-Olympic god

12 €

Charmander - pokemon with flexible articulation (seal in place, without supports)

1,50 €

Articulated axolotl

3.50 €

RS-X-Bow "Government - 1911" style

5,75 €

articulated geometry - printing on site - geométrie articulée

0,50 €

Articulated Gyarados

1. 99 €

ItsLitho "Pure" personalized lithophane Christmas ball

1,90 €

Articulated Onyx

1.50 €

Folding pipe bender

4.59 €

Halloween haunted house printed without backing or painting (Inspired by The Addams Family and Bates Motel)

4.39 €

Predator-inspired movable mask

7 € -35% 4.55 €

hinged shenron

3 €

Eeveelution articulated mega pack

10 €

Giarados - articulated sea serpent

1,50 €

Halloween pumpkin lantern ItsLitho

1,90 €

Ciberpunk 2077 Gun Rebecca "Guts"

4 €

Do you want to support Cults?

Do you like Cults and want to help us continue our journey on our own ? Please note that we are a small team of 3 people, so supporting us in maintaining activities and creating future developments is very easy. Here are 4 solutions available to everyone:

  • AD: Disable your AdBlock banner blocker and click on our banner ads.

  • AFFILIATION: Shop online by following our affiliate links here Amazon.

  • DONATIONS: If ​​you want, you can donate via PayPal here.

  • * INVITE FRIENDS: * Invite your friends, discover the platform and great 3D files shared by the community!

Mazinger Z, Drawing by Jean Marie Vandaele

© 2020 Jean Marie Vandaele

Additional Images

Let us know if you would like to see more photos of this piece of art!

  • Work side / Work side
  • Details / Signature / Surface or texture of artwork
  • artwork in the room, Other...

More photos

Let us know if you would like to see more photos of this piece of art!

  • Reverse side of work / Side of work
  • Details / Signature / Surface or texture of artwork
  • artwork in the room, Other. ..

One of a kind

Signed by the artist

Certificate of authenticity included

  • Genuine work of art Picture, Acrylic / Spray paint drawing / Ink on Paper
    • Genuine artwork

      Original artwork is any work that is considered to be authentic and not a copy or imitation of the artist's original work. Original artwork can be any kind of painting, sculpture, performance or other media. There are many types of original media. Mixed media includes oils, acrylics and watercolors. For workshop paintings that testify to craftsmanship, this attribution should be more subtle. While they may be less valuable for a variety of reasons, reproductions and copies have had a huge impact on our experience. They reach a wider audience than the originals and act as an anti-commodification tonic. The original work may also refer to the first work, which always precedes all others. It can also refer to a prototype or model from which other work can be done. Each work is very similar to the original.

    • one-of-a-kind (OOAK)

      One-of-a-kind pieces of art are also known as "OOAK" pieces of art. This means that each work of art is unique and there will never be one identical.

    • Limited Edition

      Edition is out of production. The number of copies produced is determined and indicated in the job description.

    • Open Edition

      The publication has not been completed. The production of new works continues. Works may be numbered, this also includes commissioned and print-on-demand works.

    • Unknown edition

      It is not known how many copies were made after the end of the run.

  • Dimensions Height 65cm, Width 50cm
  • Frame This work is not framed
  • Categories Drawings up to 500 € Pop Art

Portrait du héro de la famille de "GRENDIZER" alias GOLDORAK About this piece: Classification, Methods & Styles Acrylic Paint using traditional pigments mixed with synthetic. ..

Portrait du héro de la famille de "GRENDIZER" alias GOLDORAK

About this work: Classification, Methods & Styles


Paint using traditional pigments mixed with synthetic resins.

Ink A highly tinted liquid or paste used to mark paper or other print media. The design is done by hand with a plate, pen, brush or straightener. Pop art55 years old. It originated in particular in the USA with Roy Lichtenstein (1923-1997) with comic book-inspired paintings and Andy Warhol (1938-1987) who, in Reaction to Media and Advertising, will highlight these real objects, icons of the consumer society.


Drawing is a visual representation technique on a flat support. The term “drawing” denotes both the act of drawing, the resulting graphic work, and the shape of any object.

Learn more